Real double edger machine SM 26 series for household appliances

Glass edging machine is one of the earliest and largest mechanical equipment in glass deep processing equipment. Its main usage is to smooth the glass and make some special shapes. Correct and reasonable use of the glass edging machine can not only ensure the normal production, but also prolong the life of the glass machine. It is divided into single-arm special-shaped glass edging machine, linear edging machine and mould edging machine.Classification of glass edging machineGlass edging machine grinds and polishes the glass mainly through the grinding head motor and grinding wheel, ordinary signal side/double edging machine can make rough grinding, fine grinding and polishing completed in one time. Customers can choose different grinding wheels according to their own requirements.Conventional single-side glass edging machine is generally composed of the main machine (base + column + front and rear beam + grinding wheel water tank + motor + electric box, etc.), guide rail at the feed and discharge end, glass support frame, and floor water tank. Different materials and electric machine affect the accuracy and service life of the machine; Such as the base, the front and rear beams of the ordinary single-side edging machine are casting and can increase the rigidity of the machine after quenching treatment, the life is generally 10-15 years.Straight glass edging machineStraight glass edging machine is used for grinding and polishing the bottom edge, edges and corners of plate glass. The front plate is made of special telescopic press plate, the grinding head and dragging plate are all made of integral dovetail type tail slide plate. The processing speed can be adjusted arbitrarily, and it has the advantages of good rigidity, small vibration, easy debugging and high precision. Generally there are 4 grinding head /8 grinding head /9 grinding head /10 grinding head straight glass edging machine.Multistage glass edging machineMultistage side edge grinding machine is suitable for the grinding of different size and thickness of plate glass straight and 45 ° edges, rough grinding, fine grinding and polishing, chamfer process at a time, can be adjusted between 0 ° and 45 ° Angle, in the process of abrasion arbitrary adjust the feed speed and feed rate, adjust the thickness of front guide rail transformation processing glass, with a touch screen Angle and width of the chamfer, The parameters of front chamfer can be set accurately in automatic grinding. Generally there are 9 grinding head /10 grinding head multistage glass edging machine.Glass beveled glass edging machineThe beveling machine is mainly used for processing straight beveling and round bottom edge of flat glass. Grinding head using Shanghai famous brand motor with the feature of high precision, low energy consumption, and the main transmission adopts step-less speed reducer, synchronous belt transmission, the rear chain plate are made up of forging steel with heat treatment through special technology. Also, both the front and rear guide strip are made from super wear resistant materials with the strict processing technology, which can reduce the friction against the pressure plate, very effectively enhances the service life of chain plate and strip,even in the absence of lubrication can also meet the requirements of long-term use. There are lots kinds of beam beveling machine, including the front beam lifting and rear beam lifting, the former beam lifting is the most, the representative manufacturer is the GuDe glass machinery, specializing in the production of beam beveling machine, which can grind all size glass.Generally, there are 9 grinding head /10 grinding head /11 grinding head beveling machine, which is divided into large and small beveling machine. The minimum processing size of large beveling machine is 100 X100mm, the maximum width of beveling edge is generally 40mm, and the Angle is 3-25°. The minimum machining size of small beveling machine is 30x30mm, the maximum beveling width is generally 15mm, and the Angle is 3-25°. With the improvement of market processing requirements, glass machinery manufacturers have developed and produced the lifting beveling machine in the past 2 years. The minimum size is 30X30mm, the processing Angle is 0-45°, and the maximum beveling width is 35mm. As soon as this kind of machine was exhibited in China glass exhibition, it was booked by many domestic and foreign customers.Round glass edge grinding machineThis machine is suitable for grinding flat glass of different sizes and thicknesses, such as straight round edge, duck mouth, etc. It use the grinding wheel to make the rough grinding, fine grinding and polishing completed in one time. Moving the front guide rail can adjust the thickness of the glass,and the step-less reducer is used to adjust the speed at will, the speed change is stable and the accuracy is very high. Generally there are 6 grinding head /8 grinding head round glass edge grinding machine.Double straight glass edging machineIt is suitable for grinding flat glass with double straight line, rough grinding and polishing in one time. The grinding head base adopts double linear rolling guide rail and double ball screw drive to achieve stable moving speed, eliminate moving clearance, reduce resistance and wear, and ensure repeated positioning. The processing can be completed in one time by setting the parameters in the interface of PLC control system.Transmission belt drive is adjusted by the frequency conversion motor speed control system, constant power, constant torque output, stable and reliable. Polishing adopts pneumatic automatic compensation device. It is especially suitable for processing furniture glass and building glass. Generally there are 16 grinding head /20 grinding head /26 grinding head /28 grinding head double straight edge grinding machine, double grinding machine processing efficiency is high, but the price is relatively high, suitable for large tempered glass factory. Small double edge grinding machine (such as: former 2 grinding head/4 grinding head and now 6 grinding head /8 grinding head etc.) equipped with glass turntable, glass washing machine and other equipment to form a production line.Double round glass edging machineThe machine adopts PLC control system which is using the interface setting processing parameters to complete the rough grinding, fine grinding and polishing of double round edges. Frequency conversion motor can adjust the processing speed, double linear guide rail and double screw guide rail structure make it has the characteristics of convenient operation, simple structure, accurate and stable processing size, fast processing speed and so on. Generally there are 16 grinding head /20 grinding head /26 grinding head /28 grinding head double round edge grinding machine.Automatic special-shaped glass edging machineThe equipment is applied to 1mm-12mm any shape of glass, the minimum processing size is 100mm*80mm, can process both round edge and straight edge, one machine can complete Muti process including edge grinding, chamfer, polishing and other processes in one step, safe and reliable, high degree of automation, high processing efficiency.

Switchable glass is a new type of special photoelectric glass product with sandwich structure, which is composed of liquid crystal film and two layers of glass, glued by high temperature and high pressure. The user controls the transparency and opacity of the glass by controlling whether the current is on or off. The glass itself not only has the characteristics of all safety glass, but also has the privacy protection function of controlling whether the glass is transparent or not. Due to the characteristics of the liquid crystal film interlayer, the switchable glass can also be used as a projection screen to replace the ordinary curtain to present high-definition images on the glass.Switchable glass and its daily maintenanceSwitchable glass was invented and patented by researchers at Kent State University in the late 1980s. In China, people used to call switchable glass as intelligent electronic switchable glass, intelligent glass, liquid crystal glass, electronic control glass, color changing glass, PDLC glass, smart glass, magic glass, etc. Intelligent electronic control switchable glass began to enter the domestic market in 2003. Due to the high price and the lack of knowledge, it developed slowly in China in the next decade. With the sustained and rapid growth of the national economy and the rapid development of the domestic building materials market, the intelligent electronic control switchable glass has gradually been accepted by the construction and design industry and started to be applied on a large scale, With the further reduction of cost and market price, switchable glass has entered the application field of home decoration. I believe that this practical high-tech product will enter thousands of households in the near future.What are the basic maintenance methods of switchable glass? The following is for reference.1.Do not collide the glass surface with force at ordinary times. In order to prevent the glass surface from scratching, lay a tablecloth. When putting things on the switchable glass furniture, you should handle them with care and avoid collision.2.In daily cleaning, wipe it with wet towel or newspaper. In case of stains, wipe it with a towel dipped in a little beer or warm vinegar. In addition, use the glass cleaning agent currently on the market. Avoid cleaning with strong acid-base solution. In winter, the surface of the glass is easy to frost. It can be cleaned with cloth soaked in salt or wine.3.Using a cloth sprayed with detergent can also make the glass stained with oil to be clean. First of all, spray the special cleaning agent for the switchable glass, and then stick the preservative film to soften the solidified oil. After 15 minutes, tear off the preservative film, and then wipe it with a wet cloth. If you want to keep the switchable glass bright and clean, you must always clean it. If there is any writing on the glass, you can rub it with rubber soaked in water, and then wipe it with wet cloth. If there is paint on the glass, you can scrub it with cotton dipped in hot vinegar. If you wipe the glass with clean dry cloth dipped in alcohol, you can make it as bright as crystal.4.Keep away from kitchens, such as stoves. In addition, avoid wetting. Stoves should be isolated from acid, alkali and other chemical reagents to prevent erosion and deterioration.5.Switchable glass furniture placed in a more fixed place, do not randomly move back and forth, to place objects smoothly, heavy objects should be placed  at the bottom of the glass furniture, to prevent furniture center of gravity instability caused by overturning.6.Once the patterned switchable glass is dirty, you can use a toothbrush dipped with detergent to wipe it in circles along the pattern. So the glass is clean and bright.7.Glass serious scratches can not be repaired, if it is a very slight scratch can be repaired with the repair polishing wheel.

The world's photo-voltaic installed demand has increased significantly this year, and the prices of upstream and downstream products of the industry have been rising. With such a good market, the price of photo-voltaic glass has been exposed that suddenly dropped by about 30%. Is the price reduction true? What is the impact on PV module enterprises and the whole industry?Why is the price of photo-voltaic glass reduced by 30%?Recently, news of price reduction of photo-voltaic glass came out intensively in photo-voltaic industry. According to media reports, the price of 3.2mm coated photo-voltaic glass is expected to be reduced from 40RMB per square meter to less than 30 RMB per square meter. It is estimated that the price will drop by about 30%. Some organizations confirmed the news. The information analyst Wang Shuai from Zhuo Chuang also told reporters that the new price of photo-voltaic glass in April has dropped. Wang Shuai said: "in April, the new unit price: 3.2mm coating price is 28 RMB per square meter, down 30% month on month and 3.45% year on year. At present, the new orders of photo-voltaic glass machinery manufacturers are insufficient and the inventory growth is obvious. Due to the increase in inventory of some glass manufacturers, there is still room for bargaining. "It is predicted by domestic and foreign organizations that the new installed capacity of photo-voltaic in the world this year will be as high as 180gw, a year-on-year increase of 27%. The new installed capacity of photo-voltaic in China will reach 55-65gw, a significant increase compared with last year. In this context, the price of photo-voltaic glass in the upstream of the industry is cut by 30%, and there is still room for negotiation, which obviously deviates from the heat of the whole photo-voltaic market. What is the reason? According to Wang Shuai's analysis, the main reason is that the downstream PV module enterprises are squeezed by the high cost of the upstream and have reduced production. Wang Shuai said: "after the Spring Festival, the price of silicon material rose significantly, the price of battery slice rose, the cost of other raw materials such as aluminum frame, welding strip and silver paste rose. Meanwhile, the price of glass was at a high level, and the cost of component manufacturers was higher than the selling price. Therefore, the operating rate dropped, and the comprehensive production of components decreased by 35% or more."A person in the industry told reporters that at present, before the construction of domestic power stations, the cost of photo-voltaic modules is generally calculated according to the price of 1.65RMB per W, but this price is lower than the cost of module enterprises, so it is normal to reduce production. While, how good is the 30% price reduction of upstream photo-voltaic glass for module enterprises? Industry insiders said that photo-voltaic glass is only a small part of the cost of photo-voltaic modules, and the benefits brought by the price reduction are limited. At present, only when the prices of silicon and aluminum are adjusted, can the supply and demand of the whole industry chain be restored to balance. Industry insiders said: "although the demand for (components) is very good now, no one dares to supply, and no one dares to sign a large number of contracts, because they are all at a loss. If the downstream stops to put in due to the high price, the power station will not be put into operation, then the demand for components will drop, and that of silicon materials will also drop, reaching a balance. " At a recent press conference, the National Energy Administration said that photo-voltaic development will enter the stage of parity from this year, get rid of the dependence on financial subsidies, and realize market-oriented and competitive development. Industry insiders pointed out that if the price of upstream raw materials remains high, it is still a little difficult for photo-voltaic power generation to get on the grid at low price. Industry insiders said: "for example, in some places,such as Guangdong, some places in Northeast China and northern Hebei, it can be (affordable). But for most places, parity is still a little difficult to come true this year. "

On May 6th-9th, 2021, the 31st China International Glass Industry Technology Exhibition (China Glass 2021) will kick off at the Shanghai New International Expo Center. Guangdong ENKONGS Machinery Co., Ltd. (booth No.: N4-133) will also dress up for the exhibition, and look forward to communicating and cooperating with you. Enkong Glass Machinery as an influential industry event in the global glass industry in 2021, the 31st China Glass Exhibition always presents the development results of the world glass industry from a professional and international perspective, and builds a professional technology and business exchange platform for the industry on a large scale of exhibition . The 7 exhibition halls of the Shanghai New International Expo Center will be used in this exhibition.N1 hall is the International Exhibition Area,gathered the German and Italian national pavilions and many main stream brands in the world glass industry.N2 hall is for original glass film manufacturer and large comprehensive glass machine equipment manufacturer.N3\N4\N5\W5 hall are all for the glass production and glass deep processing equipment manufacturers.W4 hall is SMEs display area,concentrated in the fields of daily-use glass, decorative glass, abrasives, accessories, hardware, accessories, etc.Affected by the overseas epidemic, the number of foreign manufacturers participating in the exhibition has declined, but the confidence of main stream manufacturers in the foreign glass machine industry in participating of the exhibition remains undiminished. This exhibition will hold a series of professional technical lectures and manufacturer promotion activities. The topics cover glass deep processing new technology and equipment, sintered refractory materials, special glass new materials, silicon-based new materials, also the preparation and performance research field for  glass machine technology and equipment development and photochromic glass.At present, the domestic glass spot goods market is generally stable, shipments in some regions have slowed down slightly, and production and sales are also weaker than that of the previous period. Although the orders in processing factory are still relatively abundant, due to the high inventory both in traders and downstream chain, coupled with the end of Huber's insured price, the willingness to keep stocking up may weaken, and the pace of mid- and downstream replenishment has slowed, so the total inventory of glass manufacturers has declined slightly this week. With the acceleration of vaccination, the surge in global demand for vaccine glass bottles has boosted the market upon the sentiment.